Dorset · England

Structural engineering for two-storey extensions in Dorset

Looking for help with structural engineering in Dorset? Here's what's involved, the rules in England and what it typically costs.

Dorset at a glance

Nation
England
Price region
South West England
Postcode areas
BH, DT, SP
Towns covered
16 listed below, plus surrounding villages
Site visits
Free, no obligation

What a structural design involves

This service suits every two-storey extension, because each one needs foundations sized for two storeys and usually steel beams where walls are removed. You get a structural engineer's calculations and drawings for beams, padstones, lintels, foundations and connections, coordinated with the architectural drawings, submitted for building control and followed through on site by our build teams.

Dorset towns we list: Bournemouth (BH1), Poole (BH15), Weymouth (DT3), Christchurch (BH6), Ferndown (BH22) and Dorchester (DT1). Every other address in Dorset is covered as well.

Fees

A structural engineer (calculations and beam design) is a guide of £750–£2,200, priced in writing once the design is known.

Rules in England

In England, structural engineering is part of building regulations approval under Part A rather than planning. The engineer's calculations go to council building control or a registered building control approver with the full plans application. Where more than one contractor is involved, the Building Safety Act dutyholder rules also apply.

Approval in England: Householder planning application: £548 (or £575 for applications made from 8 December 2026). Lawful development certificate: £274 (about £288 for applications from 8 December 2026). Councils should decide householder applications within 8 weeks of validation.

Building regulations: Building regulations approval (full plans recommended) from the council or a registered building control approver, with a completion certificate at the end.

The Party Wall etc. Act 1996 applies, so notices may be needed for work on or near a shared wall or boundary.

Getting the design right

Tying into the house

The new walls and floors are tied into the existing house with wall ties, restraint straps and joist hangers. The engineer also considers movement between the old and new foundations and where a movement joint may be needed.

Foundations for two storeys

Two storeys put more load on the ground than one, so foundations are usually deeper or wider. Clay soil, nearby trees, drains and made-up ground can all mean deeper trench fill or piles, which is why we dig trial holes before fixing the design.

How we work in Dorset

  1. Start at your house

    We come to your home in Dorset, measure up, check the ground floor walls and roof structure, and note anything near the boundaries.

  2. Choose the approval route

    Some designs fit permitted development, most need a householder application. We decide which applies in England before drawing in detail.

  3. Technical design

    We prepare the building regulations drawings, structural calculations and specification so the build price can be fixed.

  4. On site

    One project lead runs the job, keeps you updated and arranges inspections at each stage until completion.

Towns we cover in Dorset

Structural engineering for two-storey extensions in Dorset: questions

How deep do foundations need to be for a two-storey extension?

There is no single depth. It depends on the soil, nearby trees, drains and the loads. On firm ground foundations may be around a metre deep, while clay near trees can need much deeper trench fill or piles. Trial holes and the engineer's design set the depth, and building control inspects the trenches.

Will the engineer visit the site during the build?

Not usually at every stage. Building control inspects the foundations, steelwork and other key stages against the approved calculations. The engineer is called back if site conditions differ from the design, such as unexpected ground, hidden beams or weak existing walls, and issues revised details before that part of the work continues.

Can a steel beam be hidden in the ceiling?

Often, yes. A beam can sit within the floor depth so the ceiling is flat, but that may mean a deeper steel section or a different floor structure. Otherwise it shows as a downstand below the ceiling. We discuss the options with you and the engineer before the design is fixed.

Neighbouring areas

All extension services in Dorset · About structural engineering for two-storey extensions

Ready to see what a second storey could do for your home?

Book a free site visit. We'll look at your house, talk through options and explain the approvals you'd need, then price the design stage in writing.

CallGuide price